JL AUDIO 10W6V3-D4

New

500 €

Add to wishlist

More info


Table_Image
Continuous Power Handling (RMS)600 W
Recommended Amplifier Power (RMS)200 - 600 W
Nominal Impedance (Znom)Dual 4 Ω

Physical Specifications

Table_Image
Nominal Diameter10.0 in / 250 mm
Overall Diameter (A)10.5 in / 267 mm
Mounting Hole Diameter (B)9.02 in / 229 mm
Bolt Hole Circle Diameter (C)9.86 in / 250 mm
Motor Outer Diameter (D)6.76 in / 172 mm
Required Pole Vent Clearance0.50 in / 13 mm
Mounting Depth (E)6.89 in / 175 mm
Driver Displacement0.078 cu ft / 2.1 L
Net Weight20 lb / 9.1 kg

Parameters

Free Air Resonance (Fs)30.12 Hz
Electrical “Q” (Qes)0.543
Mechanical “Q” (Qms)9.228
Total Speaker “Q” (Qts)0.513
Equivalent Compliance (Vas)0.821 cu ft / 23.25 L
One-Way Linear Excursion (Xmax)*0.75 in / 19 mm
Reference Efficiency (no)0.11%
Efficiency (1 W / 1 m)**82.7 dB SPL
Effective Piston Area (Sd)49.303 sq in / 0.0318 sq m
DC Resistance (Re)***6.452 Ω

* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.
** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.
*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same.

Sealed Enclosure Specifications

Table_Image
Wall Thickness0.75 in / 19 mm
Front Baffle Thickness0.75 in / 19 mm
Volume (net int.)0.55 cu ft / 15.57 L
External Width (W)12.5 in / 318 mm
External Height (H)12.5 in / 318 mm
External Depth (D)10.5 in / 267 mm
F342.27 Hz
Fc47.55 Hz
Qtc0.8099

Download detailed sealed enclosure information

Enclosure Notes
* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located around the JL Audio badge at the rear of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.
* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.
* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.
* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).
* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.

Ported Enclosure Specifications

Table_Image
Wall Thickness0.75 in / 19 mm
Front Baffle Thickness0.75 in / 19 mm
Volume (net int.)0.75 cu ft / 21.2 L
External Width (W)21.5 in / 546 mm
External Height (H)12.375 in / 314 mm
External Depth (D)11.125 in / 282 mm
Internal Slot Port Width (SW)1.375 in / 35 mm
Internal Slot Port Height (SH)10.875 in / 275 mm
Internal Slot Port Length (SL)30.40 in / 772 mm
Port Extension Length (EL)16.5 in / 419 mm
Tuning Frequency (Fb)39 Hz
F333 Hz

Download detailed ported enclosure information

Enclosure Notes
* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.
* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.
* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.
* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).
* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.